The Top 4 Reasons To Give Squadron’s New Plastic Weld A Go

The days of Velpon and Britfix 77, when you were gluing a model and strands of jelly gum draped off your model are long gone. These days, when you’re building a kit, you are using plastic cement or even better, plastic weld.

No matter the appropriate nomenclature, when you apply plastic weld or cement, you are actually melting or fusing plastic together. That said, there is still a bunch of products out there that have different properties for different uses. Some are slow drying, others are too fast and when applying, by the time you have brushed on the liquid and put the brush back into the bottle, the cement has already dried or evaporated and you have to start over the process.

Many years ago I found a certain “glue” and when I used it on the fuselage halves of my Airfix Wellington, the next morning to my horrid discovery, it left a sink line over the entire length of the model. For days it kept eating away until I finally gave up sanding. Nothing is worse when you hold a model to the light under a special angle and you notice a shallow difference, especially when you already slapped paint on it. You’ll end up with two sinks. One on your model, the other in your stomach!

Good news however. Squadron Products has released a new plastic weld under their brand name. It comes in a 1oz bottle with brush cap and I have been experimenting with it since last month on my projects. For my part I believe it has the top four elements that you should look for in a plastic cement.

  1. There is “time” to apply it.
  2. It dries fast…but not too fast!
  3. It doesn’t leave any sinkholes.
  4. And it is sand-able within one or two hours of drying time.

The latter is important, especially when dealing with fuselage and wing halves on airplane models. Another characteristic with this weld is that you can blend Squadron Putty with it, or any other putty that is lacquer based. This comes in handy when you have to apply putty in tight corners or spots that are difficult to reach. I will elaborate further on this in a later blog or article.

While we experienced difficulties in getting the bottles in, I’m happy to report that all components to get this to the marketplace have finally arrived! I encourage you all to try it out and then give us your honest feedback.

Squadron is trying very hard to look for ways to make our hobby more enjoyable and put products in place that really work and do the trick.  Personally, I am very excited about Squadron’s plastic weld. Not only because it works great for me, but because I believe my model brethren will be just as pleased as I am. This hobby has come a long way and it keeps getting better!

I still have a few ancient tubes of glue in my collection. Not that I will ever use them again, but they just remind me of bygone days treasuring the thought of my mother’s plastic tablecloth and the gap that was in there for as long as I could remember when junior didn’t close the cap properly with the jell dripping, “burning” a hole in her prized possession!

As we begin to introduce more products to the marketplace, let us know what your needs are and what products would help you enjoy the hobby more. Maybe you’ll get your wish!

P.S. Don’t forget to swing by squadron.com and give our plastic weld a go. And then, send us your honest feedback once you give it a test run…

Cheers,

JV.

Please note: I reserve the right to delete comments that are offensive or off-topic.

  • jonbius

    Hey Jef,

    How does this compare with Tamiya Extra Thin? Is it about the same viscosity? Thicker? What differentiates it from Tamiya Extra Thin? I’ve been very happy with how the Tamiya product performs, but I’m always looking for a better mousetrap.

    Thanks for your insight!

    • Jef verswyvel

      Hey there,

      It is as liquid and has the same consistency as Tamiya. It’s more a hybrid between Tamiya and Testors TS3502. Works great for me.

      Thanks

      Jef

      • Pacman

        Sounds like it acts like MEK.(Methyl Ethyl Ketone) Welds plastic together, can be used to thin paint, (spray and old stuff) and putty. I spilled a small bottle in my drawer and bonded all the loose plastic stuff to the bottom of the drawer.

  • Steve

    Need more information regarding the new Squadron Plastic Weld glue- specifically what type plastics it will bond and the MSDS data. This information should be public and would be most useful. Thanks.